Connexion

 


Sodimed sur FacebookSodimed sur TwitterSodimed sur Youtube
0 Total TTC : 0,00 € Demander un devis
Pas de produit sélectionné
Mon devis Close

A NEW AND UNIQUE ALTERNATIVE

FOR PROCESSING ATTACHMENTS INTO OVERDENTURES

Introducing Chairside a new and unique Attachment Processing Material from ZEST Anchors, the manufacturer of the trusted LOCATOR® Abutment, LOCATOR Overdenture Implant (LODI) System and SATURNO™ Narrow Diameter Implant System (SNDI). CHAIRSIDE® Attachment Processing Material was designed for ease of use and predictability when processing attachments into full and partial overdentures, using either a chairside or laboratory procedure.

Clinician input contributed to a formulation that has the most sought after handling characteristics, which requires no primer, and is self-curing — all at a reduced cost per case.* With all of these benefits, why would you choose a processing material from any other company than the leading manufacturer of overdenture products for more than 40 years - ZEST Anchors.

CHAIRSIDE Attachment Processing Material Key Attributes:

Cost Efficient
  • No primer required for reduced chairtime
  • Shorter mixing tip reduces material waste and cost per case*
  • Two size options to suit your implant practice
    • 8g (4ml) syringe for pickup of LOCATOR and SATURNO Denture Attachment Housings
    • Large 18ml cartridge ideal for full arch fixed provisional prostheses utilizing immediate load protocols such as DIEM® 2 or All-On-4®
Simple Application
  • Ideal viscosity for accurate application
  • Bonds to itself for efficient void fill and touch-ups
  • Dual cure capability provides convenient self or light cure flexibility
Patient Friendly
  • Low curing temperature ensures patient comfort
  • Odorless and tasteless to increase patient acceptance
Chairside attachment processing material diagram

6

SIMPLE STEPS

FOR CHAIRSIDE PROCESSING LOCATOR ATTACHMENTS INTO OVERDENTURES


Step 1

PLACE a White Block Out Spacer Ring around each abutment and press it down to the tissue. Place a Denture Cap with a Black Processing Male onto each abutment and press down firmly to ensure engagement of the abutment.

Chairside Step 1
Step 2

APPLY fit check marking paste inside of the denture. Insert it into the mouth in position over the Denture Caps. Mark the areas where the denture will need to be relieved to allow space for the caps to be picked up.

Chairside Step 2
Step 3

RELIEVE the areas marked with an acrylic bur. Try in the denture to verify that the Denture Caps are not in contact with the acrylic in any area. Cut lingual/palatal vent windows in the denture to visualize full seating and for excess material to vent. Cut an undercut below the intaglio surface of each Denture Cap relief area for mechanical retention.

Chairside Step 3
Step 4

DRY the Denture Caps. Apply a small amount of CHAIRSIDE Material around the circumference of each cap. Place CHAIRSIDE Material into the relief areas of the denture and seat it over the caps and onto the tissue. Have the patient close into light occlusion and hold while the CHAIRSIDE Material sets. The set time of the material from the time the material is mixed to the time it is set is five (5) minutes. The working time for the material is one (1) minute, forty-five (45) seconds.

Chairside Step 4
Step 5

DISENGAGE the denture from the abutments and remove from the mouth. Verify that the Denture Caps have been securely processed into the denture. Fill any voids, light cure and polish the denture. The material will bond to itself and will cure within 30 seconds with light application.

Chairside Step 5
Step 6

PLACE the denture in the mouth and press down to engage the males on the attachment system.

Chairside Step 6
Pas de produit dans cette catégorie

RESINE

Nos partenaires

  • IPD
  • Em Exact
  • Kuraray Noritake
  • CEKA
  • Elod Medtech
  • Dyna
  • Rhein 83
  • LV
  • Microdent
  • Locator
  • New Anchorvis